xov xwm

1. Lub kauj yog overheated thiab hlawv tawm
(1) Yog tias lub sijhawm siv ntev dhau lawm thiab dhau qhov kev tso cai, lub kauj yuav tsum tau hloov nrog ib qho tshiab thiab cov kev siv yuav tsum tau txhim kho.
(2) Lub armature yog crushed kom tuag nyob rau hauv lub sij hawm ntev energization.Lub taub hau yuav tsum tau ntxuav los yog txoj hauj lwm ntawm armature yuav tsum tau kho.
(3) Lub coil rwb thaiv tsev yog aging los yog coil yog vibrated rau luv luv-circuit rau sab hauv lem.Lub kauj yuav tsum tau hloov nrog ib tug tshiab thiab fastened nrees.

2. Tsis muaj suab nrov thiab tsis muaj kev ua haujlwm thaum lub hwj chim txuas nrog
(1) Kev sib cuag ntawm qhov hloov pauv yog nkees thiab tsis muaj zog.Hloov qhov hloov pauv lossis hloov cov khoom sib txuas.
(2) Lub hwj chim qaum yog twisted thiab lub connector yog xoob.Hloov cov hlua hluav taws xob los yog rov ua kom nruj ntawm lub connector, thiab so tawm cov sludge ntawm lub connector.
(3) Muaj cov tshuaj zawv plaub hau hauv qhov hloov pauv, uas ua rau cov khoom siv hluav taws xob raug txiav tawm.Siv txhuam hniav kom tshem tawm dandruff.

3. Muaj suab nrov electromagnetic thaum lub hwj chim qhib, tab sis lub clipper tsis ua hauj lwm
(1) Muaj ntau ntau cov dandruff nyob rau sab sauv thiab sab hniav, thiab lawv daig, thiab cov dandruff yuav tsum tau muab tshem tawm.
(2) Lub phaj ntsia hlau yog nruj heev.Cov hniav sab sauv thiab sab qis yuav tsum tau kho raws li qhov nro nruab nrab.

4. Tsis txhob noj cov plaub hau
(1) Lub kaum sab xis ntawm lub luj tshib lub taub hau tau hloov.Kho lub kaum sab xis ntawm lub kaum sab xis ntawm lub taub hau mus txog 45 degrees.
(2) Lub taub hau ntsia hlau yog xoob.Lub kaum sab xis taub hau screws yuav tsum tau nruj nreem.
(3) Cov ntsia hlau kho thiab ingot ntsia hlau yog xoob.Cov ntsia hlau yuav tsum tau hloov kho kom haum rau qhov kev vibration ntawm lub kaum sab xis ntawm lub taub hau.
(4) Qhov sib txawv ntawm sab sauv thiab qis JJ j1 loj dhau.yuav tsum tau hloov tshiab) J-thooj screws.

5. Tsis muaj pos ntse Cov hniav ntug yog hnav.Regrind cov hniav los yog hloov nrog ib tug tshiab.

6. Suab nrov Cov ntsia hlau caij nplooj ntoos hlav hloov tsis zoo.Hloov kho qhov hloov kho screws.

7. Cov dej ntws tawm
(1) Lub rwb thaiv tsev ntawm cov coil lead hlau puas lawm.Reprocess pinout rwb thaiv tsev.
(2) Lub zog qaum yog twisted thiab puas thiab sab hauv yog damp.Hloov cov hlua fais fab nrog ib qho tshiab thiab rov ua dua.